Hi,
i apply all the possible ways but it did not resolve.
> From: ayesha_comsian.hotmail.com
> To: amber.ambermd.org
> Date: Mon, 23 Nov 2015 15:36:48 +0500
> Subject: Re: [AMBER] QMMM: ERROR!
>
> i put -ek flag to the below command and it generates sqm.in , sqm.out and mol2 file
> antechamber -ek tight_p_conv=0,scfconv=1.d-8,qmcharge=0, -i sustiva_new.pdb -fi pdb -o sustiva.mol2 -fo mol2 -c bcc -s 2
> But..
> it did not show these values in the sqm.in file
> qm_theory='AM1', grms_tol=0.0002,
> and when i test the parameters through parmchk command
> parmchk -i sustiva.mol2 -f mol2 -o sustiva.frcmod
> the frcmod shows no angles the results of my frcmod file are:
> remark goes here
> MASS
>
> BOND
>
> ANGLE
>
> DIHE
>
> IMPROPER
> c3-n -c -o 10.5 180.0 2.0 General improper torsional angle (2 general atom types)
> c -c3-n -c3 1.1 180.0 2.0 General improper torsional angle (1 general atom type)
>
> NONBON
>
> how can i generate angles ? i think it is due to missing value of (qm_theory='AM1', grms_tol=0.0002)
>
>
>
>
> > From: ross.rosswalker.co.uk
> > Date: Sun, 22 Nov 2015 21:42:20 -0800
> > To: amber.ambermd.org
> > Subject: Re: [AMBER] QMMM: ERROR!
> >
> > Hi Ayesha,
> >
> > It looks like the minimizer got very close. Sometimes it just doesn't quite make it to the tolerances needed.
> >
> > You can try mimizing things separately with sqm (outside of antechamber) with scfconv=1.d-8. Then take the final structure from that and use it for your input to antechamber.
> >
> > Alternatively update to AmberTools15 which has loosened the default antechamber SQM convergence criteria slightly and in your case the SCF should then converge.
> >
> > All the best
> > Ross
> >
> > > On Nov 22, 2015, at 21:32, Ayesha Kanwal <ayesha_comsian.hotmail.com> wrote:
> > >
> > > there is an error occur during sqm.out and after that mol2 files could not generated.
> > > antechamber -i sustiva_new.pdb -fi pdb -o
> > > sustiva.mol2 -fo mol2 -c bcc -s 2
> > > the following error occured during this process
> > > Error: cannot run "/home/comsats/Desktop/Softwares/amber14//bin/sqm -O -i sqm.in -o sqm.out" of bcc() in charge.c properly, exit
> > > and the sqm.out is generating the following error
> > >
> > > RESULTS
> > > --------------------------------------------------------------------------------
> > >
> > >
> > > QMMM: ERROR!
> > > QMMM: Unable to achieve self consistency to the tolerances specified
> > > QMMM: No convergence in SCF after 1000 steps.
> > > QMMM: E = -0.3142E+07 DeltaE = -0.2242E-09 DeltaP = 0.4663E-13
> > > QMMM: Smallest DeltaE = 0.1869E-09 DeltaP = 0.2397E-06 Step = 3
> > >
> > > how can i fix this problem ?
> > > my sqm.in have these values
> > >
> > > Run semi-empirical minimization
> > > &qmmm
> > > qm_theory='AM1', grms_tol=0.0002,
> > > tight_p_conv=1, scfconv=1.d-10, qmcharge=0,
> > >
> > >
> > >
> > > _______________________________________________
> > > AMBER mailing list
> > > AMBER.ambermd.org
> > > http://lists.ambermd.org/mailman/listinfo/amber
> >
> >
> > _______________________________________________
> > AMBER mailing list
> > AMBER.ambermd.org
> > http://lists.ambermd.org/mailman/listinfo/amber
>
> _______________________________________________
> AMBER mailing list
> AMBER.ambermd.org
> http://lists.ambermd.org/mailman/listinfo/amber
_______________________________________________
AMBER mailing list
AMBER.ambermd.org
http://lists.ambermd.org/mailman/listinfo/amber
Received on Mon Nov 23 2015 - 04:30:04 PST
