Dear Elvis Martis
Thanks for your reply !
MY problem is :
According to AMBER Tutorial B0 ,I first run minimization for my system, then heating MD and finally production MD (npt ,then nvt).
only run minimization and heating MD with sander.MPI existing "System must be very inhomogeneous" errors, and the end of the production MD can be normal.
Another question: the end of all steps can be normal if run MD simulation with pmemd.MPI.
Error information are as following:
>***** Processor 7
>***** System must be very inhomogeneous.
>***** Readjusting recip sizes.
> In this slab, Atoms found: 580 Allocated: 531
>
>
>***** Processor 9
>***** System must be very inhomogeneous.
>***** Readjusting recip sizes.
> In this slab, Atoms found: 540 Allocated: 531
>
>
>***** Processor 7
>***** System must be very inhomogeneous.
>***** Readjusting recip sizes.
> In this slab, Atoms found: 532 Allocated: 531
My input files are:
For run minization:
Initial minimisation(MM)
&cntrl
imin=1, maxcyc=16000, ncyc=4000,
ntf=1, ntc=1,
cut=8.0, ntb=2, ntp=1
/
For heat MD :
Heat 100 ps MD temp:0-300(MM)
&cntrl
imin=0,ntx=1,irest=0,
ntf=2, ntc=2, ntp=0,
cut=8.0, ntb=1,
tempi=0.0, temp0=300,
nstlim=100000, dt=0.001 ,
ntpr=1000, ntwx=1000,ntwr = 1000,
ntt=3,gamma_ln=2.0,
nmropt=1,ig=-1
/
&wttype='TEMP0',istep1=0,istep2=85000,value1=0.0,value2=300 /
&wttype='TEMP0',istep1=85001,istep2=100000,value1=300,value2=300 /
&wt type='END' /
At 2017-03-05 18:28:54, "Elvis Martis" <elvis.martis.bcp.edu.in> wrote:
>HI,
>Does your simulation crash?? Can you tell us little more about your system?
>There are similar posts on this http://archive.ambermd.org/201108/0444.html
>http://archive.ambermd.org/201209/0040.html
>
> Best Regards
>
>
>
>Elvis Martis
>Ph.D. Student (Computational Chemistry)
> at Bombay College of Pharmacy
>
>
>A Kalina, Santacruz [E], Mumbai 400098, INDIA
>W www.elvismartis.in
>Skype. adrian_elvis12
>
>
>
>
>-----Original Message-----
>From: 杨满意 [mailto:ymy0664.163.com]
>Sent: Sunday, March 05, 2017 9:41 AM
>To: amber.ambermd.org
>Subject: [AMBER] Amber 16 MD simulation Problems
>
>Hi,
> when I us amber 16 to do simulation, I always have the following probems
>
>
>***** Processor 7
>***** System must be very inhomogeneous.
>***** Readjusting recip sizes.
> In this slab, Atoms found: 580 Allocated: 531
>
>
>***** Processor 9
>***** System must be very inhomogeneous.
>***** Readjusting recip sizes.
> In this slab, Atoms found: 540 Allocated: 531
>
>
>***** Processor 7
>***** System must be very inhomogeneous.
>***** Readjusting recip sizes.
> In this slab, Atoms found: 532 Allocated: 531
>
>
>
>
>My inputfile:
> Heat 100 ps MD temp:0-300(MM)
> &cntrl
> imin=0,ntx=1,irest=0,
> ntf=2, ntc=2, ntp=0,
> cut=8.0, ntb=1,
> tempi=0.0, temp0=300,
> nstlim=100000, dt=0.001 ,
> ntpr=1000, ntwx=1000,ntwr = 1000,
> ntt=3,gamma_ln=2.0,
> nmropt=1,ig=-1
> /
>&wttype='TEMP0',istep1=0,istep2=85000,value1=0.0,value2=300 /
>&wttype='TEMP0',istep1=85001,istep2=100000,value1=300,value2=300 / &wt type='END' /
>
>
>
>
>How can I solve these problems. Thanks!
>
>
>_______________________________________________
>AMBER mailing list
>AMBER.ambermd.org
>http://lists.ambermd.org/mailman/listinfo/amber
>_______________________________________________
>AMBER mailing list
>AMBER.ambermd.org
>http://lists.ambermd.org/mailman/listinfo/amber
_______________________________________________
AMBER mailing list
AMBER.ambermd.org
http://lists.ambermd.org/mailman/listinfo/amber
Received on Mon Mar 06 2017 - 03:00:03 PST
