CPU type is r16000. I checked it as follows:
***************************
$ hinv
2 600 MHZ IP35 Processors
CPU: MIPS R16000 Processor Chip Revision: 2.1
FPU: MIPS R16010 Floating Point Chip Revision: 2.1
Main memory size: 2048 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Integral SCSI controller 2: Version IDE (ATA/ATAPI) IOC4
Integral SCSI controller 0: Version QL12160, low voltage differential
Disk drive: unit 1 on SCSI controller 0
Disk drive: unit 2 on SCSI controller 0
Integral SCSI controller 1: Version QL12160, single ended
IOC3/IOC4 serial port: tty3
IOC3/IOC4 serial port: tty4
IOC3/IOC4 serial port: tty5
IOC3/IOC4 serial port: tty6
Gigabit Ethernet: tg0, module 001c01, PCI bus 1 slot 4
Gigabit Ethernet: tg1, module 001c01, PCI bus 2 slot 1
Gigabit Ethernet: tg2, module 001c01, PCI bus 2 slot 2
IOC3/IOC4 external interrupts: 1
************************************
On Wed, 18 Jul 2007, Carlos Simmerling wrote:
> what is the CPU on your origin? you could change -r16000 to your CPU type.
>
> On 7/18/07, Ruchi Sachdeva <rsachdeva.webmail.imtech.res.in> wrote:
>> Dear all,
>>
>> I am trying to compile AMBER (version9) on a SGI IRIX64 origin 6.5 with
>> SGI mips compiler.
>>
>> I installed it as follows:
>> ***************
>> $ ./configure sgi_mips
>> AMBERHOME is set to /data/users/ruchi/amber9
>> Setting up Amber configuration file for architecture: sgi_mips
>> Using parallel communications library: none
>>
>> The configuration file, config.h, was successfully created.
>> *****************
>>
>> Things are fine till this step. Then I compiled it,
>>
>> *************
>> $ make serial
>> Starting installation of Amber9 (serial) at Wed Jul 18 20:09:15 PDT 2007.
>> cd lib; make install
>> /lib/cpp -P -DSGI -DnoVDINVSQRT new2oldparm.f > _new2oldparm.f
>> f90 -c -n32 -mips4 -r16000 -O0 -o new2oldparm.o _new2oldparm.f
>> f90 ERROR parsing -r16000: unknown flag
>> *** Error code 2 (bu21)
>> *** Error code 1 (bu21)
>> ******************
>>
>> I got above error. I searched through archive but could not find any
>> solution. Can anybody please tell me how to fix this error?
>>
>> Any help is appreciated!
>>
>> Thanks in advance
>> -----------------------------------------------------------------------
>> The AMBER Mail Reflector
>> To post, send mail to amber.scripps.edu
>> To unsubscribe, send "unsubscribe amber" to majordomo.scripps.edu
>>
> -----------------------------------------------------------------------
> The AMBER Mail Reflector
> To post, send mail to amber.scripps.edu
> To unsubscribe, send "unsubscribe amber" to majordomo.scripps.edu
>
-----------------------------------------------------------------------
The AMBER Mail Reflector
To post, send mail to amber.scripps.edu
To unsubscribe, send "unsubscribe amber" to majordomo.scripps.edu
Received on Sun Jul 22 2007 - 06:07:23 PDT
