At the begining, the temperature keeps stable. But the temperature goes up quickly before it stops.
----- Original Message -----
From: Carlos Simmerling <carlos.simmerling.sunysb.edu>
Date: Thursday, May 29, 2003 4:56 pm
Subject: Re: MD problem
> what do the temperatures etc look like up
> until it stops? is it stable, or did the T go up?
> Carlos
>
> ----- Original Message -----
> From: "Shuang Ding" <sd517.nyu.edu>
> To: <amber.heimdal.compchem.ucsf.edu>
> Sent: Thursday, May 29, 2003 4:47 PM
> Subject: MD problem
>
>
> > Hi,
> >
> > I'm running an MD simulation of a DNA 11-mer damaged covalently
> with a
> bulky adduct attached to one base. However the simulation was
> stopped after
> 50ps of production in AMBER 7 with error message:
> > " vlimit exceeded for step 50582; vmax = 26.05232686120750
> > vlimit exceeded for step 50583; vmax = 24.16632764793692
> > EWALD BOMB in subroutine ewald_list
> > volume of ucell too big, too many subcells
> > list grid memory needs to be reallocated, restart sander"
> >
> > Equilibration was performed normally as in the DNA tutorial
> (minimized for
> 1000 steps of steepest descent, followed by 50ps dynamics with DNA
> fixed to
> relax the water, then minimized for 1000 additional steps of steepest
> descent, follow by 3ps dynamic with 25kcal/mol restraints on the
> DNA, five
> rounds minimization of 600 steps with restraint reduced by
> 5kal/mol each
> round, from 20 to 0kal/mol. Finally heated up from 10k to 300k
> over 40ps,
> and additional 20ps unrestrained dynamics for equilibration.)
> >
> > This happens after 58ps of production in AMBER6 too, with error
> message:> “ vlimit exceeded for step 58303; vmax =
> 187.5334023293732> COORDINATE RESETTING CANNOT BE ACCOMPLISHED,
> > DEVIATION IS TOO LARGE
> > NITER, NIT, LL, I AND J ARE : 0 4 63 172 173”
> >
> > This is my input file for both AMBER 6 and 7:
> > &cntrl
> > ntx = 7, irest = 1, ntrx = 1, ntxo = 1,
> > ntpr = 100, ntwx = 500, ntwv = 0, ntwe = 0,
> > ntwprt = 0, ntwr = 500,
> >
> > ntf = 2, ntb = 2, dielc = 1.0,
> > cut = 12.0, nsnb = 10,
> > scnb = 2.0, scee = 1.2,
> >
> > ipol = 0,
> > ibelly = 0, ntr = 0,
> >
> > imin = 0,
> > nstlim = 200000,
> > nscm = 1000,
> > t = 0.0, dt = 0.001,
> >
> > temp0 = 300.0, tempi = 300.0,
> > ig = 71277, heat = 0.0,
> > ntt = 1, dtemp = 0.0,
> > tautp = 1.0,
> > vlimit = 20.0,
> >
> > ntp = 1, pres0 = 1.0, comp = 44.6,
> > taup = 1.0, npscal = 1,
> >
> > ntc = 2, tol = 0.000001,
> > &end
> >
> > Could anyone give some suggestion to solve this problem? Thanks
> a lot.
> >
> >
> >
>
>
Received on Thu May 29 2003 - 22:53:00 PDT
